EPOXY Floor Primer & Top Coat EP 40 KIT ( Grey or Clear

Wykamol EP 40 Grey 5kg (Epoxy Floor Coating) kit

NO MORE DAMP EP40. Water based floor coating system which consists of the EP40 Epoxy Floor Primer and EP40 Epoxy Finish coat, available in grey or clear.

NO MORE DAMP EP40 Floor Primer is designed to soak into the substrate, block pores, improve adhesion and ensure an even, high quality finish. After the final application of EP40 Epoxy Finish Coat, floors become easier to clean with a hard-wearing, dust-free, waterproof and impervious finish and are substantially more resistant to damage by fork-lift trucks, chemical, fuels and lubricants.

To be used on concrete floors in a variety of commercial and industrial environments, including:

• Industrial plants
• Commercial and retail stores
• Warehouses
• Hospitals
• Showrooms
• Garages
• Gymnasiums

Special Features:

• Food preparation areas
• Can be applied to green concrete after 7 days
• Ideal for areas in contact with vehicles, such as forklifts and lorries
• Ideal for areas with high foot traffic
• Excellent adhesion to concrete and wood
• Floor becomes easier to clean due to the impervious finish
• Makes the substrate substantially more resistant to chemicals, fuels and lubricants
• Provides attractive, dust-free finish
• Can be used internally and externally
• Can be used as a liquid DPM (damp-proofing membrane) at ground level

Coverage of approx 30 to max 40m2 according to the condition of the concrete surface.

TYPICAL USES:

Over concrete floors in a variety of commercial and industrial environments, such as:

• Industrial plants

• Commercial and retail stores

• Warehouses

• Hospitals

• Showrooms

• Garages

• Gymnasiums

• Industrial food preparation areas

APPLICATION:

EP40 Epoxy Floor Primer:

1. Using a stiff brush or roller, work the product into the substrate, ensuring all areas are completely covered.

2. Allow to cure for at least 12 hours prior to applying a second coat of primer or EP40 Epoxy Finish Coat. If atmospheric or substrate temperatures are below 20°C, allow for a longer initial curing time. Product should be just tack free.

3. Depending on porosity and texture of substrate, 2 coats may be necessary.

4. Do not allow Primer to fully cure - do not allow curing time to exceed 36 hours before applying a 2nd coat of Primer or Finish Coat.

EP40 Epoxy Finish Coat:

1. When using EP40 Epoxy Finish Coat in clear, perform a small test application in an inconspicuous area, to ensure the finish is as desired.

2. One coat of EP40 Epoxy Finish Coat in clear or grey can be applied with a brush or roller, aiming for a continuous coating.

3. Spread the product as thinly as possible while achieveing maximum coverage. Ensure no pooling or excess product remains.

4. Only 1 application of EP40 Epoxy Finish Coat is necessary for areas which will experience light traffic, such as school corridors. 2 coats should be applied in areas of medium traffic, such as warehouses.

Achieving Slip Resistance:

1. Slip resistance can be improved by scattering anti-slip aggregates onto the EP40 Epoxy Finish Coat, whilst still wet, and back rolling at a rate of 75 g/m². Following intial cure (16 - 24 hours), apply a second coat of EP40 Epoxy Finish Coat to secure the aggregates.

APPLICATION CONDITIONS AND LIMITATIONS:

• ONLY apply system at temperatures between 10°C and 30°C. Applying at temperatures under 10°C will significantly inhibit curing.

• DO NOT apply to substrates, or in atmospheric conditions, with > 80% humidity.

• DO NOT use any kind of steam cleaning on the treated surface, even after full cure.

• DO NOT subject NO MORE DAMP EP40 Epoxy Floor Coating System to high levels of UV light, even after full cure.

• DO NOT use on floors experiencing hydrostatic pressure from groundwater.

Product Data Sheet